This design has two options, one with the servo in horizontal orientation and one in vertical orientation. Both designs allow very high uptilt at or greater than 45 degrees. This is the base design and is intended to be used with the Universal Camera Mount. Guide for 3D printing the gimbal design here. Files onContinue reading “FPV Gimbal – Project 399 Super G / Super G Plus / Super G 10″ – LDX-218”
Category Archives: Gimbal Design
FPV Gimbal – Holybro Kopis CineWhoop 3″ – LDX-218
This design has two options, one with the servo in horizontal orientation and one that conserves space by putting the servo vertical. Both designs will require the rear to be zip tied down to the top plate as there is no standoffs there to bolt to, this is similar to the Shen Drones Squirt design,Continue reading “FPV Gimbal – Holybro Kopis CineWhoop 3″ – LDX-218”
FPV Gimbal – GEPRC Crocodile7 – LDX-218
This design is for the base of the gimbal and is intended to be used with the Universal Camera Mount. Guide for 3D printing the gimbal design here. Files on Thingiverse: https://www.thingiverse.com/thing:5152279 Design commissioned by: Dominic Herrera If the Universal Mount doesn’t work with this base or for your application this design is compatible withContinue reading “FPV Gimbal – GEPRC Crocodile7 – LDX-218”
FPV Gimbal – Universal Camera Mount
This is a FPV gimbal design that accepts any camera via the standard action camera ‘tab’ mount. This is compatible with all existing kits and tutorials and with almost all of the existing Medlin Drone gimbal designs, mounting on the standard Medlin Drone 20mm bearing housing, and will work with analog, DJI, and Shark Byte,Continue reading “FPV Gimbal – Universal Camera Mount”
Dual-Axis FPV Gimbal
I have finally tried building and flying a dual axis FPV gimbal, with camera pitch and roll being dynamically controlled via head tracking. I wanted to know if this would be possible to fly in acro, how difficult it would be to learn, and if it would be practical. I want to briefly discuss whatContinue reading “Dual-Axis FPV Gimbal”
FPV Gimbal – ImpulseRC Apex – LDX-218
This is the base design is intended to be used with the 20mm Universal Camera Mount. Guide for 3D printing the gimbal design here. Files on Thingiverse: https://www.thingiverse.com/thing:5040991
FPV Gimbal – QAV-S / QAV-S JB Edition – LDX-218
This is the base design is intended to be used with the 20mm Universal Camera Mount. Guide for 3D printing the gimbal design here. Files on Thingiverse: https://www.thingiverse.com/thing:5041010
FPV Gimbal – AOS 5 / 5.5 / 7 / Cine35 – LDX-218
This is the base design and is intended to be used with the 20mm Universal Camera Mount. Guide for 3D printing the gimbal design here. Files on Thingiverse: https://www.thingiverse.com/thing:5040239
FPV Gimbal – Rotor Riot CL1 / HD1 / XR – LDX-218
This is the base design and is intended to be used with the 18mm Universal Camera Mount. It will fit both the normal and XR versions, the base is specific to the CL1 and HD1 as they have different bolt patterns. Guide for 3D printing the gimbal design here. Files on Thingiverse: https://www.thingiverse.com/thing:5031319
FPV Gimbal – T-Motor FT5 MKII V2 HD – LDX-218
This is a designfor the T-Motor FT5 MKII V2 HD, I have chosen to reverse the drone and use the back as the front in order to not move the DJI Air Unit, but I am including options for both normal and reverse orientation. Guide for 3D printing the gimbal design here. Files on Thingiverse:Continue reading “FPV Gimbal – T-Motor FT5 MKII V2 HD – LDX-218”